SDS OF ECOAMIDE 6 TOUGH
-
IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND COMPANY/UNDERTAKING
-
PRODUCT NAME:POLYOXYMETHYLENE HOMOPOLYMER, ACETAL HOMOPOLYMER
-
BRAND NAME:ECOTAL 1000S, 5000S, 9000S
-
SUPPLIER:INTERTECH LIMITED
2-23-1 Ogi Adachi-Ku Tokyo, Japan
-
-
COMPOSITION, INFORMATION ON INGREDIENTS
INGREDIENT NAME CAS NUMBER Base Resin 24969-26-4 This product may contain proprietary ingredients. This is a polymeric material. All constituents are wetted by the polymer system. This product is considered hazardous under OSHA Regulations due to the release of formaldehyde if overheated, OSHA regulated material.
-
HAZARDS IDENTIFICATION
-
NFPA RATINGS (SCALE 0-4):HEALTH=1, FIRE=1, REACTIVITY=0
-
EMERGENCY OVERVIEW:Pellets or powder with slight to no odor. Combustion and decomposition may produce hazardous fumes. Base resin dust/powder has a US Bureau of Mines relative dust explosion hazard rating of severe. Molten material can cause thermal burns on contact with skin or eyes. Spilled pellets may create a slipping hazard. Overheating may result in release of formaldehyde, which may irritate the eyes and respiratory tract.
-
POTENTIAL HEALTH EFFECTS:
-
ROUTES OF EXPOSURE:Skin and eye contact; inhalation of vapors, if overheated.
-
SIGNS AND SYMPTOMS OF EXPOSURE:No specific information available concerning exposure to the product. If formaldehyde is released as an off-gas, a burning sensation and tearing of the eyes may occur. An irritating odor may be noted.
-
IMMEDIATE EFFECTS:INHALATION: No specific information available on the product. Pellets are not considered an inhalation hazard; polymer dust/flake may be considered an inert nuisance particulate. Formaldehyde, which may be released if overheated, may cause irritation of the upper respiratory tract.
-
EYE CONTACT:No specific information available on the product. Polymer particles can cause mechanical irritation. Degradation vapors may cause irritation.
-
INGESTION:No specific information available on the product. However, low toxicity by this route is expected based on the biological activity of high molecular weight polyacetal polymers.
-
LONG TERM/DELAYED EFFECTS:No specific information available on the product. Formaldehyde may cause respiratory sensitization.
-
CARCINOGENICITY:No specific information available on the product. OSHA, a probable human carcinogen by The International Agency for Research on Cancer (IARC, 2A), and a substance, which can reasonably be anticipated to be a carcinogen by The National Testing Program (NTP), list formaldehyde as a potential cancer hazard. Formaldehyde should not pose a risk if exposures are kept below the OSHA Permissible Exposure Limit. The International Agency for Research on Cancer (IARC) has evaluated carbon black, which may be contained in this product, and found it to be possibly carcinogenic to humans (Group 2B). Any carbon black in this product is wetted by the polymer system, and therefore, present no likelihood of exposure under normal conditions of processing and handling.
-
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURES:No specific information available on the product. Off-gases, which may be released if overheated, may affect those with chronic diseases of the respiratory system.
-
-
FIRST AID MEASURES
-
INHALATION:Remove to fresh air, Seek medical attention if breathing difficulties occur.
-
SKIN CONTACT:Remove contaminated clothing, jewelry, and shoes immediately. Wash with soap or mild detergent and large amounts of water until no evidence of chemical Remains (at least 15-20 minutes). Get medical attention, if needed.
-
EYE CONTACT:Wash eyes immediately with large amounts of water or normal saline, Occasionally lifting upper and lower lids, until no evidence of chemical remains. Get medical attention immediately.
-
INGESTION:If vomiting occurs, keep head lower than hips to help prevent aspiration. Get medical attention, if needed.
-
NOTE TO PHYSICIANS:This product is essentially inert and nontoxic. However, if it is overheated or burns, gases such as carbon monoxide and formaldehyde may be released. Those exposed to off-gases may need to have their arterial blood gases and carboxyhemoglobin levels checked. If the carboxyhemoglobin levels are normal and the exposure occurred in an enclosed space, asphyxia (carbon dioxide replacing oxygen) is a possibility. Formaldehyde is a respiratory irritant gas. If patients may have inhaled high concentrations of irritating fumes they should be monitored for delayed onset pulmonary edema.
-
-
FIRE FIGHTING MEASURES
-
FLASHPOINT:> 93 deg C (> 200 deg F) by Tag Closed Cup Method. Base resin dust/powder has a US Bureau of Mines relative dust explosion hazard rating of severe.
-
HAZARDOUS PRODUCTS OF COMBUTION:Carbon monoxide and carbon dioxide.
-
EXTINGUISHING MEDIA:Carbon dioxide, regular dry chemical, regular foam, water spray.
-
FIREFIGHTING INSTRUCTIONS:Firefighters should wear self-contained breathing apparatus and full fire-fighting turnout gear (bunker gear). Keep personnel removed from and unwind of fire. Water should be used to keep fire-exposed containers cool. Product burns with a very hot, but very faint blue flame. Water, foam and dry chemical may cause damage to electrical equipment.
-
-
ACCIDENTAL RELEASE MEASURES
-
IN CASE OF SPILL OR OTHER RELEASESweep or vacuum material and place in container for re-use or disposal. Spills and releases may have to be reported to Federal and/or local authorities.
-
-
ACCIDENTAL RELEASE MEASURES
Sweep or gather up spills and place in proper container for recovery or disposal. Keep unnecessary people away, isolate hazard area and deny entry.
-
HANDLING AND STORAGE
-
HANDLING:Do not handle hot or molten material without appropriate protective equipment. Maintain good housekeeping in work areas. Do not exceed recommended process temperature to minimize release of decomposition products. Do not smoke in areas where polymer dust is present. Appropriate measures should be taken to control the generation and accumulation of dust during conveying and processing operations.
-
STORAGE:Store in a cool dry place. Maintain dryness of resin.
EXPOSURE CONTROLS, PERSONAL PROTECTION
-
EXPOSURE GUIDELINES:
-
POLYOXYMETHYLENE COPOLYMER:No occupational exposure limits established by OSHA, ACGIH or NIOSH.
-
COMPONENT OR HAZARDOUS DEGRADATION PRODUCT:FORMALDEHYDE
– OSHA PEL (Permissible Exposure Limit): TWA – 0.75 ppm/8 hr, STEL – 2 ppm
ACGIH TLV: 0.3ppm ceiling
– MAK = 0.5ml/m3 – 0.6mg/m3 (Germany)
(TRGS 500 (Germany) Group III B)
– VME = 0.5 ppm, VLE = 1 ppm
(Circular of work Ministry of the 19th of July 1982: TR82/38 n (11453, RECT, TR82/46)
CARBON BLACK
– OSHA PEL (Permissible Exposure Limit): 3.5-mg/cu m
ACGIH TLV: 3.5 mg/cu m
NUISANCE/INERT DUST
– OSHA PEL (Permissible Exposure Limit): 15-mg/cu m (total)
5-mg/cu m (respirable)
NUISANCE PARTICULATES
– ACGIH TLV: 10 mg/cu m (total)
3-mg/cu m (respirable) -
VENTILATION:Given suitable ventilation, it can be assumed that the threshold limits will not be reached. Provide local exhaust ventilation system. Ventilation equipment should be explosion- resistant if explosive concentrations of material are present. Ensure compliance with applicable exposure limits.
-
PROTECTIVE EQUIPMENT:
-
EYES:Safety eyewear recommended
-
SKIN:When thermal or melt processing, wear long pants, long sleeves, well insulated gloves, and face shield when there is a chance of contact
-
INHALATION:A NIOSH approved respirator is recommended if there is a possibility of dust generation above permissible exposure limits or that decomposition vapors may be generated.
-
-
PHYSICAL AND CHEMICAL PROPERTIES
-
PHYSICAL FORM:solid/pellets
-
MELTING POINT:175 deg C
-
VAPOR PRESSURE:< 0.001mm Hg
-
SPECIFIC GRAVITY:1.38 – 1.42
-
WATER SOLUBILITY:negligible < 0.1%
-
VOLATILES:< 1.0% by weight
-
ODOR:slight characteristic odor
-
-
STABILITY AND REACTIVITY
-
REACTIVITY:Stable under normal conditions of use and storage.
-
CONDITIONS TO AVOID:Avoid heat, flames, sparks and other sources of ignition. Avoid contact with incompatible materials. Do not heat above 235 deg C. Avoid prolonged heating at or above the recommended processing temperature. Recommended melt temperatures 180 – 200 deg C.
-
INCOMPATIBILITIES:Strong acids and oxidizing materials. Do not compound with PVC or halogen-containing materials, and partially and/or fully cross-linkable thermoplastic Elastomers
-
HAZARDOUS DECOMPOSITION:Trioxane, formaldehyde, and formic acid.
-
POLYMERIZATION:Will not polymerize.
-
-
TOXICOLOGICAL INFORMATION
No specific information available on the product.
-
ECOLOGICAL INFORMATION
-
ECOTOXICITY:No specific information available on the product.
-
ENVIRONMENTAL INFORMATION:this material is considered to be non-biodegradable.
-
-
DISPOSAL CONSIDERATIONS
Recycling is encouraged. Dispose in accordance with all applicable regulations.
-
TRANSPORT INFORMATION
Not classified as hazardous under transport regulations
-
REGULATORY INFORMATION
-
U.S. REGULATIONS:All components are listed on the TSCA Inventory.
- TSCA: All the ingredients of this product comply with TSCA Inventory Regulations.
- SARA: This product does not contain any toxic chemicals subject to the reporting requirements of Section 313 of the Emergency Planning and Community Right-to-Know Act of 1986 and of 40 CFR 372.
- LABELING ACCORDING TO EEC Directives: Not subject to labeling.
- GERMANY REGISLATION/REGULATIONS:
Not classified according to German “Hazardous Substance” regulations.
-
-
OTHER INFORMATION
The information contained herein is based on the present state of our knowledge and does not therefore guarantee certain properties.
Recipients of our product must take responsibility for observing existing laws and regulations.
Inquiry
製品について、
その他お気軽にお問い合わせ下さい。